JAI : CV-A436
Description
This product has been discontinued. For an alternative solution, please contact sales.
The JAI CV-A436 is a remote micro head camera (17 mm dia.) with a 1/3″ monochrome progressive scan CCD sensor and with features similar to the CV-A11. The small and lightweight head makes the CV A436 ideal for applications with space or mass constraints, such as semiconductor equipment or robotics. The CVA436 camera features a standard frame rate of 60 fps with programmable exposure, shutter speeds from 1/60 to 1/200,000 second, partial scanning, and other features. The camera head is connected to the controller by a 2-meter detachable cable.
AI offers newer products with similar functionality as the CV-A436. Therefore, the CV-A436 will be phased out in near future and JAI recommends that this product is not considered for new design-in projects. Please contact JAI to hear about alternative products.
Features
→ Remote head 1/3" progressive scan monochrome camera
→ 17⌀ x 46mm head with 2m cable
→ 659 (h) x 494 (v) square pixels (VGA format)
→ 60 frames per second single channel video output
→ High S/N ratio >53 dB
→ Shutter speeds from 1/60 to 1/200,000 second in 15 steps in continous mode
→ Shutter speeds from 1/60 to 1/20,000 second in 10 steps in EPS modes
→ Programmable exposure with 1H steps. (31.8 μs)
→ Partial scanning 1/2, 1/3 and 1/6 for higher frame rates
→ Internal, external HD/VD or random trigger synchronization
→ Edge pre-select, pulse width control, start/stop trigger modes
→ Long time exposure with external VD pulse interval
→ Frame-delay readout in connection with pulse width controlled shutter
→ Exposure enable EEN, write enable WEN and pixel clock output
→ Short ASCII commands for fast mode setup via serial port
→ Setup by Windows NT/2000/XP software via RS 232C
Specifications
| Scanning system | Progressive 525 lines, 60 frames/sec. |
| Pixel clock | 24.54 MHz |
| Line frequency | 31.46 KHz. (780 pixel clock/line) |
| CCD sensor | Monochrome 1/3" IT CCD |
| Sensing area | 4.9 (h) x 3.7 (v) mm |
| Cell size | 7.4 (h) x 7.4 (v) μm |
| Effective pixels | 659 (h) x 494 (v) |
| Pixels in video output. Full | 648(h) x 492 (v) 60 frames/sec. |
| Pixels in video output. 1/2 partial | 648(h) x 240 (v) 112 frames/sec. |
| Pixels in video output. 1/3 partial | 648(h) x 160 (v) 158 frames/sec. |
| Pixels in video output. 1/6 partial | 648(h) x 80 (v) 268 frames/sec. |
| Pixels in video output. Sensitivity on sensor | 0,1 Lux (Max gain, 50% video) |
| S/N ratio | >53 dB |
| Video output (with/without sync.) | Composite VS signal, 1 Vpp, 75 Ω Video signal 0.7 Vpp |
| Gamma | 1.0 or 0.45 |
| Gain | Manual - Automatic |
| Gain range | Man.: -3 to 12 dB - Auto.: 0 to 12 dB |
| Synchronization | Int. X-tal. Ext. HD/VD or random trigger |
| HD/VD sync. input/output | 4 Vpp ±2 V, 75 Ω (or TTL input) |
| Trigger input | 4 Vpp ±2 V, TTL |
| WEN output (write enable) | 4 V, 75 Ω |
| EEN output (exposure enable) | 4 V, 75 Ω |
| Pixel clock output | 4 V, 75 Ω |
| Trigger modes | Continuous, EPS, PWC, Long time, Start/Stop and Smearless |
| Readout modes | Frame delay, Smearless, Partial |
| Trigger accumulation | HD synchronous or HD a-synchronous |
| Shutter speed, Continuous | 1/60 to 1/200,000 second |
| Shutter speed, EPS | 1/60 to 1/20,000 second |
| Programmable exposure | 1.5 H to 525 H |
| Pulse width control | 1 H to 1000 H |
| Start/stop | 1/60 to 1/20,000 second |
| Long time exposure | 2 frames to ∞ |
| Frame-delay readout | Time from PWC trigger input to ext. VD input |
| Smearless readout | Reduced smear at high shutter speeds |
| Functions controlled by RS 232C | Trigger mode, shutter speed, shutter mode, scanning, gain, timing signal polarity |
| Functions controlled by internal DIP switches | VD input/output, HD input/output, HD and VD 75Ω termination on/off |
| Operating temperature | -5°C to 45°C |
| Humidity | 20 - 80% non-condensing |
| Storage temp./humidity | -25°C to 60°C/20% - 80 % non-condensing |
| Vibration | 10G (20Hz to 200 Hz XYZ) |
| Shock | 70G |
| Regulations | CE (EN50081-1, EN50082-2), FCC part 15 |
| Power | 12V DC ± 10%. 2 W |
| Lens mount thread | M15.5 x 0.5 |
| Dimension/weight cam. head | ø17 x 46 mm. 25 g excluding cable |
| Cable length | 2m. detechable at control unit |
| Dimensions control unit | 29 x 44 x 66 mm (HxWxD) |
| Weight control unit | 150 g |
Resources & Documents
| cv-a436.pdf | Datasheet |