JAI : AD-081GE
Description
This product has been discontinued (as of March, 2019). For an alternative solution, please contact sales.
The AD-081GE is a 2-monochrome prism-mounted progressive scan CCDs (1/3”). It has two I/O connectors configurable for separate or combined output and programmable GPIO with opto-isolated inputs and outputs.
Features
→ AD-081GE 2-monochrome prism-mounted progressive scan CCDs (1/3")
→ Member of the C3 Advanced series
→ 1024 (h) x 768 (v) active pixels per channel
→ 4.65 micro m square pixels
→ 30 frames/second with full resolution
→ 60 frames/second for interleaved high frame rate operation
→ Increased frame rates with partial scan or vertical binning
→ PIV (Particle Image Velocimetry) mode also available
→ Programmable exposure from 20 micro s to 33 m s
→ Auto shutter and GenICam Exposure Time Abs modes
→ Exposure time up to 2 sec. using Pulse Width trigger mode
→ Sequence trigger mode for on-the-fly change of gain, exposure and ROI
→ LVAL synchronous/asynchronous operation (auto-detect)
→ Programmable GPIO with opto-isolated inputs and outputs
→ Two I/O connectors configurable for separate or combined output
→ Comprehensive control tool and SDK for Windows XP /Vista
Specifications
| Sensor 1 | 1/3" Monochrome IT CCD (ICX204AL) |
| Sensor 2 | 1/3" Monochrome IT CCD (ICX204AL) |
| Pixel Clock | 33.75 MHz |
| Frame rate (HDR mode) | 30 frames/sec. |
| Frame rate (interleaved) | 60 frames/sec. |
| Active area | 4.76 (h) x 3.57 (v) mm |
| Cell size | 4.65 (h) x 4.65 (v) micro m |
| Active pixels | 1024 (h) x 768 (v) |
| Read-out modes, Full | 1024 (h) x 768 (v) 30/60 fps |
| Read-out modes, Variable partial | Programmable start line: 1 to 760. Programmable height: 8 to 768 lines |
| Read-out modes, Vertical binning | 1024 (h) x 384 (v) 49.3 fps max. |
| Sensitivity | 0.34 Lux (On sensor, max. gain, shutter off, 50% video) |
| S/N ratio | >54dB (Gain 0 dB, shutter off) |
| Video output | Dual monochrome 8, 10, or 12 bit, GigE Vision output Synchronized or separate timing via 2 RJ-45 connectors. Output selectable to one or both channels |
| Auto-iris lens video | 0.7 Vp-p, 75 ohm NUM luminance signal w/o sync |
| Gain | Manual or AGC: -3dB to 21dB |
| Synchronization | Int. X-tal |
| GPIO Module, Input/output switch | Configurable 21-in/14-out switch |
| GPIO Module, Clock generator (one) | 12-bit counter based on pixel clock |
| GPIO Module, Pulse generator (four) | 20-bit counters with programmable length, start point, stop point, repeat |
| Hardware Trigger modes | Edge Pre-Select, Pulse Width Control, Reset Continuous, PIV, Frame Delay, Sequence |
| Electronic shutter, Programmable exposure | 0.5L (20micro s) to 792L (33.3ms) in 1L steps (42.07micro s) |
| Electronic shutter, Exposure Time Abs | micro sec - user definable. Same range as PE |
| Electronic shutter, GPIO plus Pulse Width | 20 micro s to 2 sec. |
| Electronic shutter, Auto shutter | 1/30 to 1/10,000 sec. |
| Pre-processing functions | Auto gain balancing, blemish compensation, shading correction, knee point/slope, LUT/gamma correction |
| Control interface | Register based, GigE Vision/GenICam compliant. |
| Functions controlled via GigE Vision interface | Shutter, gain, black level, trigger mode, read-out mode, GPIO setup, ROI (GenICam mandatory functions) |
| GigE Vision streaming protocol | Packet size (up to 16020 bytes), delayed (frame) read-out, inter-packet delay |
| Indicators on rear panel | Power/hardware trigger, GigE link/activity |
| Operating Temperature | -5°C to 45°C |
| Humidity (operation) | 20 - 80% non-condensing |
| Storage temp./humidity | -25°C to 60°C / 20 to 80% |
| Vibration | 3 G (15Hz to 200 Hz XYZ) |
| Shock | 50G |
| Regulations | CE (EN 61000-6-2, EN-61000-6-3), FCC part 15 class B, RoHS |
| Power | 12V - 24V DC ± 10%. 7.6 W typical (full frame @ 12V) |
| Lens mount | C-mount (use 3CCD type, Max. 4.0 mm thread) |
| Dimensions (H x W x L) | 55(H) x 55(W) x 98.3(D) mm |
| Weight | 320 g |