NVT : NV-8PS13-PVD
Description
The NVT 8 Channel Power Supply Passive Receiver Hub NV-8PS13-PVD is a key hybrid component that consolidates all CCTV system cabling using standard EIA/TIA 568B structured building wiring. Designed for installation in the IDF/Telecom Closet or MDF/Equipment Room, the Power Supply Passive Video Receiver Hub has independently selectable 24VAC-OFF-28VAC outputs that can support at-distance camera loads up to 1 Amp per channel. Use with NVTs PVD transceivers for cable runs under 750ft (225m) .
The NV-8PS13-PVD has built-in passive receiver hub that allows connection to DVR or an encoder for IP transmission. Per-channel diagnostic LEDs display load /no-load, miswires, or fault conditions at a glance. Automatic-reset fault protection, transient protection, and ground loop free individually floating outputs.
Features
NV-8PS13-PVD features include:
→ Video Frequency response DC to 10 MHz
→ Video Attenuation 0.5 dB typ
→ Each output is individually thermistor protected
→ Each output is individually thermistor protected for auto-reset after fault removal
→ Provides Class 2 SELV camera power while receiving video transmission and delivering P/T/Z telemetry all over a single 4-pair Cat5e cable
→ Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B
→ Independently selectable 24VAC-OFF-28VAC with 1 Amp per channel
→ Automatic-reset fault protection; transient protection
→ Frequency Response DC to 10 MHz
→ Individually floating outputs ensure total ground-loop immunity
→ Diagnostic LEDs show load/no load, miswires, and overload conditions
→ Use with the NV-216A-PV, NV-218A-PVD or the NV-226J-PV transceiver at the camera
→ Power cameras via UTP over significant distances (see Power Distance Calculator)
→ 1U high; 8" deep; wall, desk, or rack-mountable, 2ft (60cm) BNC Cables included
→ Limited lifetime warranty
Specifications
| Video Common-mode / Differential-mode rejection | 15 KHz to 5 MHz 60 dB typ |
| Video Impedance Coax, female BNC | 75 ohms |
| Video Impedance UTP, RJ45 | 100 ohms |
| Video Network Wiring | One four-pair Cat5 or better per channel |
| Camera Power | Fully isolated (floating) Class 2 SELV output, individually switchable 24VAC/OFF/28VAC at up to 1 Amp. |
| Power inlet | IEC with molded power cord (included) |
| Power Voltage | 115 / 230 VAC |
| Power Current | 2.5 / 1.25 Amps |
| Power Protection | 5x20mm type T fuse 2.5Amp 250V |
| Power Wattage | 250 Watts |
| Power Heat | (power supply only) 100 BTU/hour (power supply with cameras) 900 BTU/hour |
| Power Output | Fully isolated (floating) Class 2 SELV ouput, individually switchable 24VAC / off / 28VAC at up to 1 Amp |
| System Power | Blue LED |
| Per-channel LED indicates Off | No load connected |
| Per-channel LED indicates Green | Load connected and working |
| Per-channel LED indicates Amber | Mis-wiring detected |
| Per-channel LED indicates Red | Overload shutdown condition |
| Ambient Temperature | -4 to 122 °F (-20 to 50 °C) |
| Minimum airflow | 4ft3/min (0,1m3/min) |
| Humidity (non-condensing) | 0 to 95% |
| Transient Immunity | per ANSI 587 C62.41 |
| Dimensions, including connectors | 19in wide, 1.73in high, 12in deep 43cm wide, 4,5cm high, 20cm deep |
| Weight | 14lb (6,35kg) |
| Mounting | Rack mount L brackets for front, rear, or wall installations; rubber feet for desk applications |
| Cables | Eight 2ft (60cm) coax jumpers; Molded IEC power inlet cord 7ft (200cm) |
Resources & Documents
| nv-8ps13-pvd.pdf | Datasheet |