
NVT : NV-4PS13-PVD
Description
The NVT 4 Channel Power Supply Passive Receiver Hub NV-4PS13-PVD is a key hybrid component that consolidates all CCTV system cabling using standard EIA/TIA 568B structured building wiring. Designed for installation in the IDF/Telecom Closet or MDF/Equipment Room, the Power Supply Passive Video Receiver Hub has independently selectable 24VAC-OFF-28VAC outputs that can support at-distance camera loads up to 1 Amp per channel. Use with NVTs PVD transceivers for cable runs under 750ft (225m) .
The NV-4PS13-PVD has a built-in passive receiver hub that allows connection to DVR or an encoder for IP transmission. Per-channel diagnostic LEDs display load /no-load, miswires, or fault conditions at a glance. Automatic-reset fault protection, transient protection, and ground loop free individually floating outputs.
Features
NV-4PS13-PVD features include:
→ Video Frequency response DC to 10 MHz
→ Video Attenuation 0.5 dB typ
→ Each output is individually thermistor protected
→ Provides Class 2 SELV camera power while receiving video transmission and delivering P/T/Z telemetry all over a single 4-pair Cat5e cable
→ Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B
→ Independently selectable 24VAC-OFF-28VAC with 1 Amp per channel
→ Automatic-reset fault protection; transient protection
→ Frequency Response DC to 10 MHz
→ Individually floating outputs ensure total ground-loop immunity
→ Diagnostic LEDs show load/no load, miswires, and overload conditions
→ Use with the NV-216A-PV, NV-218A-PVD or the NV-226J-PV transceiver at the camera
→ Power cameras via UTP over significant distances (see Power Distance Calculator)
→ 1U high x 8 deep wall, desk or desk rack-mountable
→ Limited lifetime warranty
Specifications
Video Common-mode / Differential-mode rejection | 15 KHz to 5 MHz 60 dB typ |
Video Impedance Coax, female BNC | 75 ohms |
Video Impedance UTP, RJ45 | 100 ohms |
Video Network Wiring | One four-pair Cat5 or better per channel |
Camera Power | Fully isolated (floating) Class 2 SELV output, individually switchable 24VAC/OFF/28VAC at up to 1 Amp. |
Power inlet | IEC with molded power cord (included) |
Power On-off switch | Rear panel |
Power Voltage | 115 / 230 VAC |
Power Current | 1.25 / 0.625 Amps |
Power Frequency | 50 / 60 Hz |
Power Protection | 2.5A slo-blo 8x20mm fuse and thermal shutdown |
Power Wattage | 125 Watts |
Power Heat | (power supply only) 50 BTU/hour (power supply with cameras) 420 BTU/hour |
Blue LED | System power on |
Per-channel LED indicates Off | No load connected |
Per-channel LED indicates Green | Load connected and working |
Per-channel LED indicates Amber | Mis-wiring detected |
Per-channel LED indicates Red | Overload shutdown condition |
Ambient Temperature | -4 to 122 °F (-20 to 50 °C) |
Humidity (non-condensing) | 0 to 95% |
Transient Immunity | per ANSI 587 C62.41 |
Dimensions | 9.25in wide, 1.75in high, 7.25in deep |
Including connectors | (235mm wide, 44,5mm high, 184mm deep) |
Mounting | Wall, or desk mount |
Product Weight | 7lb (3,2kg) |
Packaged Weight | 8.42lb (3,8kg) |
Resources & Documents
nv-4ps13-pvd.pdf | Datasheet |