Hitachi KP-FD30CL VGA Progressive Scan CCD Color Camera
Industrial Video System & Broadcast

Hitachi : KP-FD30CL
Description
The Hitachi KPFD30CL is equipped with the progressive full frame RGB output of high frame rate(approx. 60 frame per second). Small lightweight size, since adoption of multi-connector with one cable. By adoption of the progressive scan CCD image sensor and RGB primary color mosaic filters, the picture of high vertical resolution and high color fidelity can be acquired. It outputs Camera-Link.
The Hitachi KP FD30CL is equipped the external synchronization(HD/VD), the external trigger function, etc., it is suitable for the image-processing equipment input. It can be set as the image output of NTSC system (2:1 interlace scan) by switch change.
Specifications
Imaging device | 1/2-inch progressive scan interline CCD |
No. of effective pixels | 659(H) x 494(V) |
Unit cell size | 9.9(H) x 9.9(V) m ( Square pixel ) |
Scanning area | 7.48(H) x 6.15(V) mm |
Color filter | R, G, B primary color mosaic fi lters on chip |
Scanning system (Selectable by switch) | Progressive scan ( VGA mode ); 2:1 interlace scan ( NTSC mode ) |
Frequency | Horizontal: 31.468 kHz Vertical: 59.94 Hz |
Sync system | Internal / external ( HD/VD auto selection ) |
Internal sync output | HD/VD/SYNC 2 Vp-p/75 , Negative polarity; WE: 5 Vp-p, Negative |
External sync input | HD/VD 2 to 5 Vp-p, Negative polarity; EXT. Trigger input: Low 0 VDC, High 2 to 5 VDC |
Video signal output | RGB output (G on SYNC); Y/C output ( Only at the NTSC mode ); VBS output ( Only at the NTSC mode) |
Resolution ( Y signal at center ) | Horizontal: 440 TV lines; Vertical: 480 TV lines ( VGA mode ) 350 TV lines ( NTSC mode ) |
Standard sensitivity | 2,000 lx ( F5.6, 100IRE ) |
Minimum illumination | 10 lx ( F1.4, AGC ON, 50IRE ) |
Sensitivity selection | Gain Adjustable at AGC OFF and AGC Limit Gain |
Electric shutter speed | Selectable in 11 steps high spped shutter |
PRESET | OFF(1/60), 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000, 1/30000, 1/50000 second: Approx. 1H steps from 1/60 second to 1/10,000 second; Selectable in 27 steps low speed shutter OFF(1/60), 1/30, 1/15, 1/10, 1/7.5, 1/6, 1/5, 1/3.75, 1/3, 1/2.5, 1/2, 1/1.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8 second |
AES | From 1/60 second to approx. 1/50,000 second ( Response : SLOW, NORMAL, FAST ) |
VARIABLE | Approx. 1H steps from 1/60 second to 1/10,000 second |
Auto level ontrol [ALC] | ( The auto level control system of AES, lens iris and AGC. ); AVERAGE / PEAK&AVERAGE / AREA ( Scanning area is selectable from 9 area. ) |
Auto-iris lens outputs [DC/VIDEO*] | DC ( Iris control voltage input type lens, cable length over 150mm ): Coupling coil impedance Damper : 1,150 ±10% , Drive : 190 ±10% |
Power supply | 12 VDC, 60 mA |
Note | “VIDEO” is optionally. |
White balance | Selectable in 3 modes; Auto-tracking[ATW]:2,500K~6,000K; preset [AWC] : (2,500K~10,000K); R/B gain manual control [MANUAL] (2,500K~10,000K) |
Text display | 24 alpha-numeric characters in one line |
Picture adjustment | Modes and settings can be selected |
Remote control | Modes and settings can be selected and adjusted from PC by RS-232C level |
Power supply | 12 VDC ± 10 %; Approx.370mA (Including 60mA for auto-iris lens ) |
Lens mount | C/CS mount (Frange-back adjustment) |
Ambient temperature – Operating | -10 to 50°C, ( 14 to 122 °F) 30 to 80 %RH |
Storage | -20 to 60°C(-4 to 144 °F), 20 to 90 %RH |
Vibration endurance | 68.6 m/s2 ( 10 to 200Hz, 30 minutes each on XYZ axes ) |
Shock endurance | 490 m/s2 ( vertical, horizontal, once each face ) |
External dimensions | 58(W) x 58(H) x 48(D) ( not including lens and protrusions ) |
Mass | Approx.220g ( without lens ) |
Resources & Documents
kpfd30.pdf | Spec Sheet |